75 lines
2.4 KiB
Bash
Executable File
75 lines
2.4 KiB
Bash
Executable File
#!/bin/sh
|
|
# Step: Extract original BIOS from both EEPROM chips
|
|
#
|
|
# Order rationale: read 4MB (top) chip first — smaller, faster,
|
|
# surfaces setup issues (clip alignment, voltage, ribbon) sooner.
|
|
|
|
# Read a chip with inline retry on failure.
|
|
# $1 = output filename
|
|
# $2 = human label (e.g. "4MB (top) — read 1 of 2")
|
|
_read_with_retry() {
|
|
_out="$1"
|
|
_label="$2"
|
|
|
|
while true; do
|
|
info "Reading $_label ..."
|
|
if run_cmd "sudo flashrom --programmer ch341a_spi -r $_out"; then
|
|
return 0
|
|
fi
|
|
|
|
echo ""
|
|
warn "Read failed. Most common causes:"
|
|
echo " - Clip not seated flush on chip (try pressing down gently)"
|
|
echo " - Pin 1 misaligned (red wire must match chip's dot/notch)"
|
|
echo " - Laptop still has residual power (remove battery + CMOS)"
|
|
echo " - Cheap SOIC-8 clips can make intermittent contact"
|
|
echo ""
|
|
echo " 1) Re-seat clip and retry"
|
|
echo " 2) Abort"
|
|
echo ""
|
|
printf "${CYAN}Choice [1-2]:${NC} "
|
|
read -r _choice
|
|
case "$_choice" in
|
|
1) continue ;;
|
|
*) return 1 ;;
|
|
esac
|
|
done
|
|
}
|
|
|
|
step_extract_bios() {
|
|
section "Extract Original BIOS"
|
|
|
|
info "The T440p has two EEPROM chips beside the SODIMM slots:"
|
|
echo " - 4MB (top) — smaller SOIC-8, farther from CPU"
|
|
echo " - 8MB (bottom) — larger SOIC-8, closer to CPU (holds ME firmware)"
|
|
echo ""
|
|
info "Each chip is read twice so we can diff the results and catch flaky reads."
|
|
echo ""
|
|
|
|
# Show reference image for chip locations
|
|
show_image "eeprom_chips_location.png" "Reference: EEPROM chip locations on T440p mainboard"
|
|
echo ""
|
|
|
|
cd "$WORK_DIR" || return 1
|
|
|
|
# --- 4MB chip (do first: smaller = faster iteration on setup) ---
|
|
echo ""
|
|
info "Clip the CH341A onto the ${BOLD}4MB (top)${NC} chip."
|
|
info "Align the red ribbon wire with the dot/notch on the chip (pin 1)."
|
|
prompt_continue
|
|
|
|
_read_with_retry "4mb_backup1.bin" "4MB chip (read 1 of 2)" || return 1
|
|
_read_with_retry "4mb_backup2.bin" "4MB chip (read 2 of 2)" || return 1
|
|
success "4MB chip reads complete."
|
|
|
|
# --- 8MB chip ---
|
|
echo ""
|
|
info "Now move the clip to the ${BOLD}8MB (bottom)${NC} chip."
|
|
info "Re-check pin 1 alignment before pressing down."
|
|
prompt_continue
|
|
|
|
_read_with_retry "8mb_backup1.bin" "8MB chip (read 1 of 2)" || return 1
|
|
_read_with_retry "8mb_backup2.bin" "8MB chip (read 2 of 2)" || return 1
|
|
success "8MB chip reads complete."
|
|
}
|